Understanding Essential Plumbing Skills is Essential for Bathtub Installation
Understanding Essential Plumbing Skills is Essential for Bathtub Installation
Blog Article
We've discovered this great article on How to Install a Bathtub Yourself below on the internet and thought it made sense to share it with you in this article.
Mounting a tub isn't exactly rocket science, but it does require strong plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a moderately hard task. If the old bathtub is easily easily accessible, the job can move easily; if you need to open up a wall surface to get rid of the old tub and also place the brand-new tub, the job is a lot harder. In either instance, the job is within a residence handyman's skills, although you will certainly require a helper to move out the old bathtub as well as set in the new one. Make sure you have actually qualified yourself for the job and fit attempting it. As opposed to working with a contractor to take control of a halfway-completed project, it is better to consider using one prior to you begin. Chances are you might require a specialist plumber to make tube connections.
This short article will help you mount a new bath tub in your bathroom if you have actually currently purchased a new bathtub as well as do not need to alter the setup of your previous supply of water pipelines.
Your devices and material list must consist of the following:
Getting ready for the Setup
To start with, the sustaining frame supplied with the bathroom should be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the tap includes a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the versatile tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its final setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water system. After doing so, turn on the taps to drain pipes any water remaining in the system. The procedure of getting rid of the existing taps can be fairly troublesome because of the restricted accessibility that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a cloth all set for the staying water that will certainly originate from the pipelines. When the supply pipelines have been removed, use the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing substance.
Prior to carrying on to fit the new faucets, contrast the pipe connections on the old taps to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bath tub
Using the two wood boards under its feet, place the bath tub in the required setting. The wooden boards are useful in equally spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little points.
The following objective is to guarantee that the tub is leveled all round. This can be achieved by examining the level and changing the feet on the bathtub up until the spirit level checks out degree.
To install taps, fit the bottom of the outermost versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system and examine all joints as well as new pipework for leaks and also tighten them if needed. Fill up the bathtub as well as also check the overflow outlet and the normal electrical outlet for leaks.
Finally, take care of the bath paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bathtub should wait till the bathtub has been made use of at least once as this will certainly resolve it right into its final placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a link to the current supply pipes.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin making certain that the washing machines are in place in between the tap and the sink. Protect the tap in position with the producer given backnut. Once the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular faucet ports. The previous kind ought to be attached to the faucet finishes first, tightening up just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to break an inflexible seal, causing the water to penetrate the wall between the bath and the tiling, causing complications with moisture and feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your fixtures and installations. They are marketed in tubes and also cartridges, as well as can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Remember to always load the tub with water prior to securing, to enable the movement experienced when the tub remains in usage. The sealant can fracture fairly very early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise easily offered on the market. It is suggested to fit the floor tiles using water-resistant or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
I'm very eager about How to Install a Bathtub and I hope you enjoyed the entry. Sharing is good. You won't know, you might be helping someone out. I thank you for reading our article about A Step-by-Step Guide to Installing a Bathtub.
Emergency leaks? Professional help here. Report this page